Диагностика Abs |
Здравствуйте, гость ( Вход | Регистрация )
Диагностика Abs |
19.10.2018, 19:02
Сообщение
#1
|
|
Зарегистрированный пользователь Группа: NISMO-CLUB Сообщений: 127 Регистрация: 20.10.2010 Из: Красноярск Пользователь №: 19134 Автомобиль: Skyline V35 |
Как сделать самодиагностику ABS ?
Загорается иногда abs и гаснет. Иногда издаёт звуки при начале движения |
|
|
19.10.2018, 19:37
Сообщение
#2
|
|
Зарегистрированный пользователь Группа: NISMO-CLUB Сообщений: 4176 Регистрация: 14.6.2006 Из: Ангарск Пользователь №: 3986 Автомобиль: CPV35 Turbo |
Тормозухи чуть выше метки подлей.
Понаблюдай... -------------------- 06`CPV35/MT6/VQ35DET/Cosworth/Eagle/ACL/ARP/Supertech/Cometic/MOCAL/
KAKIMOTO RACING/FUJITSUBO/Greddy/HKS/OBX RACING/AEROMOTIVE/UpRev Project HP = Stock HP x 1,9 Бортовой журнал |
|
|
19.10.2018, 23:57
Сообщение
#3
|
|
Зарегистрированный пользователь Группа: NISMO-CLUB Сообщений: 324 Регистрация: 25.5.2007 Из: Odessa Пользователь №: 7346 |
|
|
|
20.10.2018, 11:10
Сообщение
#4
|
|
Зарегистрированный пользователь Группа: NISMO-CLUB Сообщений: 127 Регистрация: 20.10.2010 Из: Красноярск Пользователь №: 19134 Автомобиль: Skyline V35 |
|
|
|
20.10.2018, 19:05
Сообщение
#5
|
|
Зарегистрированный пользователь Группа: NISMO-CLUB Сообщений: 162 Регистрация: 14.4.2015 Из: Это Питер детка) Пользователь №: 32422 Автомобиль: Skyline V35 250GT |
|
|
|
20.10.2018, 22:30
Сообщение
#6
|
|
Зарегистрированный пользователь Группа: NISMO-CLUB Сообщений: 324 Регистрация: 25.5.2007 Из: Odessa Пользователь №: 7346 |
Это диагностика, а не самодиагностика. что в лоб, что по лбу.... пробуй такой вариант BRAKE CONTROL SYSTEM Цитата Self-Diagnosis NFS000KQ DESCRIPTION If a malfunction is detected in system, ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp on meter turn on. In this case, perform self-diagnostic as follows: OPERATION PROCEDURE 1. Turn ignition switch OFF. 2. Perform “CONSULT-II Start Procedure”. Refer to GI-37, "CONSULT-II Start Procedure" . 3. Turn ignition switch ON. 4. Start engine and drive vehicle at approximately 30 km/h (19 MPH) or more for approximately 1 minute. 5. After stopping vehicle, with engine still idling, touch “SELF-DIAG RESULTS” on CONSULT-II screen in this order. CAUTION: Just after starting engine, or turning ignition switch ON, “ABS” may not be displayed on system selection screen even if “START” is touched. In this case, start self-diagnostic again from step 1. If it cannot be shown after several attempts, VDC/TCS/ABS control unit may have malfunctioned. Repair or replace control unit. 6. Self-diagnostic results is displayed. (If necessary, touch “PRINT” to print self-diagnostic results.) ● When “NO FAILURE” is shown, check ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp. Refer to BRC-32, "For Fast and Accurate Diagnosis" . ● CONSULT-II self-diagnostic results are displayed without regard to occurrence timing. In some cases later ones (timing value is small) appear on next screen. 7. Conduct the appropriate inspection from the display item list, and repair or replace the malfunctioning component. 8. Start engine and drive vehicle at approximately 30 km/h (19 MPH) or more for approximately 1 minute. CAUTION: Check again to make sure that there is no malfunction on other parts на всякий случай ещё вот тебе. Сообщение отредактировал 200sx_pilot - 20.10.2018, 23:29 |
|
|
Текстовая версия | Сейчас: 25.4.2024, 15:48 |